E-bike Handleiding | Harry's Tweewielers

Harry's Two-Wheelers

E-bike manual

G a g o e d v o o r b e r e i d o p p a d

E-bike manual Pointer Edenta.

Read the steps carefully.

You activate the bike by turning on the switch at the back at the bottom of the battery. The rear light will now light up and will burn continuously while riding.
Now press the middle button on the mini display for 1 second, the display will light up.
4 blocks on the left side indicate that the battery is full, it will decrease blocks during the ride. The first block can take quite a long time.
1 block on the right side indicates that the support is in position 1. This is the position for riding away and also making long trips. (80 km is easily feasible in this position).
With the plus and minus arrows you can adjust the support to your preference up to 4 blocks. (remember, it will now go very fast and the consumption will therefore also increase considerably, riding away only in position 1).
Front light. Hold the up arrow button for a moment (remember that the support does not go up unnoticed).
Reset trip meter, Press the middle button on the display briefly, the total distance changes to daily distance. Now hold the middle and bottom buttons until the day counter reads 0000.

Locking the bike correctly is important!

When the bicycle is not in use it must always be double locked with the lock and chain.

Charging works as follows.

When renting for multiple days, you will receive a charger. After the ride, let the battery rest for a while (15 minutes). Plug the charger with the 3-pin plug on the right rear side into the battery. Then plug the plug into the socket. The light on the charger will now light up red. When the light turns green, the battery is full again.
To remove the battery, the bike must be locked. With the 2nd key in the battery to the left, it can be released. You can then slide the battery out (sometimes a bit difficult). You can now charge the battery inside. After charging, slide the battery back into the sled properly and calmly and lock it again.

In case of failure, first try:

If the rear light is on but the display does not come on, check whether the battery is properly connected in the sled.
Several malfunctions can be caused by a loose plug under the saddle to the battery sled. Check whether these four plugs are secured.
For other malfunctions, contact the rental company.

G a g o e d v o o r b e r e i d o p p a d

E-bike manual Pointer Kyra.

Read the steps carefully.

You activate the bike by briefly pressing the on button on the control on the left side of the handlebars.
The display will now turn on. Here you can see, among other things, the battery charge, which will decrease during the ride.
The support mode. These can be operated with the plus and minus buttons on the left side of the handlebars. 1, 2 and 3 are support when cycling
4 and 5 are the power modes. The bike goes very fast and uses a lot of battery power.
Accidents also usually happen in these modes. Be careful!!
You can also operate the light on the left side of the handlebars.
The trip meter is reset automatically.

Locking the bike correctly is important!

When the bicycle is not in use it must always be double locked with the lock and chain.

Charging works as follows.

When renting for multiple days, you will receive a charger. After the ride, let the battery rest (15 minutes). The charger can be inserted into the battery at the top right. Then plug it into the socket. The light on the charger will now light up red. When the light turns green, the battery is full.
To remove the battery, the bike must be locked. With the second key on the right side at the top of the frame, you can unlock the battery and remove it.
After charging, place the battery at the bottom and press it at the top. The battery is in place if it cannot be released without the key and the display works (see Riding).

In case of failure, first try:

Check that the battery is properly seated in the holder.
Several faults can be caused by a loose connector under the saddle to the battery slide. Check that they are all properly secured.
Check under the saddle that the 4 connectors to the battery slide are still properly secured.

G a g o e d v o o r b e r e i d o p p a d

E-cargo bike manual Bakfiets.nl

Read the steps carefully.

You activate the bike by turning on the on/off switch on the right side of the battery holder under the handlebars.
5 blocks at the top indicate that the battery is full, these will decrease during the ride.
On the left side, the support is indicated with blocks. Set this to position 1 to ride away and also make long trips. (80 km is easily feasible in this position).
With the plus and minus arrows you can adjust the support to your preference up to 3 blocks. (remember, it will now quickly become very fast and consumption will therefore also increase considerably, only ride away in position 1).
With the lighting button on the display you can switch on the lighting.
Reset trip meter, Briefly press the middle button on the display until the daily distance is displayed. (range is the distance still to be ridden and ODO is the total distance) Now hold the middle button until the trip meter flashes. Now press the middle and plus buttons together until the trip meter is at 0000.

Locking the bike correctly is important!

When the bicycle is not in use it must always be double locked with the lock and chain.

Charging works as follows.

When renting for multiple days, you will receive a charger. After the ride, let the battery rest for a while (15 minutes). Plug the charger into the battery on the left rear side with the white arrow at the top. Then plug the plug into the socket. The light on the charger will now light up. When the light goes out, the battery is full again. The battery indicator will now show 5 green lights.
To remove the battery, the bike must be locked. By turning the 2nd key in the battery to the left, it can be released and you can slide the battery out to the side. You can now charge the battery indoors (for this you need the separate adapter that is attached to the cord with a Tyrib). After charging, the battery can be placed back in the holder until it clicks back into the lock.

In case of failure, first try:

If the display does not turn on, check whether the battery is properly seated in the holder.
If there are any other problems, please contact the rental company.